Just How to Replace a Bathtub Yourself: Removing and also Replacing.
ExterminatorIn this article down the page you might get additional excellent points about How to Install a Bathtub.
Installing a bath tub isn't exactly brain surgery, however it does call for solid plumbing, woodworking, and occasionally, tiling skills. Changing an old bathtub with a brand-new one is also a reasonably hard project. If the old bathtub is readily easily accessible, the project can relocate rapidly; if you need to open a wall surface to remove the old tub and also position the brand-new bathtub, the job is much harder. In either situation, the task is within a house handyman's abilities, although you will need an assistant to move out the old tub and also set in the new one. See to it you have qualified on your own for the work as well as fit attempting it. Instead of employing a specialist to take control of a halfway-completed project, it is far better to consider employing one before you begin. Possibilities are you may need a specialist plumber to make tube links.
This short article will certainly aid you mount a brand-new tub in your washroom if you have already gotten a brand-new tub as well as do not require to change the arrangement of your previous water system pipelines.
Your tools and material list need to consist of the following:
Preparing for the Installation
To start with, the sustaining frame supplied with the bath ought to be fitted (if needed) according to the supplier's guidelines. Next off, fit the taps or mixer to the bathtub. When fitting the tap block, it is very important to make certain that if the tap comes with a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bath, it is additionally sensible to fit a sustaining plate under the faucets device to stop strain on the bathtub.
Fit the versatile tap ports to the bottom of the two taps utilizing 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet through the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bathroom. See to it you utilize all of the supplied washers.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bathroom need to currently be ready to be fitted in its last placement.
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your setup, then the first thing you should do is separate the water. After doing so, switch on the taps to drain any kind of water staying in the system. The process of removing the existing faucets can be rather problematic as a result of the limited gain access to that is typically the case.
Make use of a container wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipelines to the faucets. Have a cloth all set for the staying water that will come from the pipes. As soon as the supply pipes have been eliminated, use the very same device to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from turning throughout this process. Once the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned up of any old securing compound.
Prior to proceeding to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Installing the Bath tub
Using both wooden boards under its feet, position the bathtub in the needed position. The wood boards are helpful in uniformly spreading the weight of the tub over the area of the boards rather than concentrating all the weight onto four small factors.
The next objective is to ensure that the tub is leveled all round. This can be attained by inspecting the level and changing the feet on the bath tub up until the level reads level.
To mount taps, fit all-time low of the outermost flexible faucet adapter to the appropriate supply pipe by making a compression sign up with; after that do the very same for the other tap.
Turn on the water and check all joints as well as new pipework for leakages and also tighten them if necessary. Fill the tub and likewise examine the overflow electrical outlet and the normal outlet for leaks.
Lastly, take care of the bath paneling as described in the maker's user's manual. Tiling and sealing around the tub ought to wait up until the tub has actually been utilized at the very least when as this will certainly resolve it right into its last placement.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic adapter to stop damages to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end supplies a link to the current supply pipelines.
If you require to fit a monobloc, after that you will certainly need minimizing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next off, position the tap in the mounting hole in the bath/basin guaranteeing that the washers remain in area in between the tap as well as the sink. Secure the tap in position with the supplier given backnut. As soon as the faucet is safely in place, the supply pipes can be connected to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with regular faucet ports. The former type should be attached to the faucet finishes first, tightening just by hand. The supply pipelines can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the area where the bathroom fulfills the floor tile, it is needed to secure the accompanies a silicone rubber caulking. This is very important as the fitting can move enough to fracture an inflexible seal, creating the water to permeate the wall between the bath and also the tiling, bring about issues with moisture as well as possible leakages to the ceiling listed below.
You can select from a range of coloured sealants to assimilate your components as well as fittings. They are sold in tubes and also cartridges, as well as are capable of securing voids as much as a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with twists of drenched newspaper or soft rope. Remember to constantly fill the bath tub with water before sealing, to enable the movement experienced when the bathtub remains in usage. The sealant can fracture relatively early if you do not take into account this activity before sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally quickly available on the marketplace. It is a good idea to fit the tiles making use of water-resistant or waterproof sticky and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As an enthusiastic reader on How to Install a Bathtub Yourself, I thought sharing that blog post was a great idea. Are you aware of somebody else who is excited about How to Install a Bathtub Yourself? Do not hesitate to share it. I praise you for your time. Come back soon.
Estimate Free